AUTOMATIC DOOR SWEEP
On request, Univer and Proget doors are available with an automatic door sweep to prevent air drafts from entering through the crack between the leaf and the floor. It complements the FF sealing applied to the frame to provide better acoustic insulation and better air sealing for the door.
It is applied on the push side by using screws to attach it directly to the sheet metal of the door, after which the mechanism is completely covered with an anodized aluminum profile. On request, it can also be provided in the same color as the door leaf.
It is applied on site following door installation so that it can be adjusted to the actual leaf height.
| Lengths avail. | FM L active leaf | FM L secondary leaf |
|---|---|---|
| 430 mm | from 500 to 520 | from 407 to 506 |
| 530 mm | from 521 to 620 | from 507 to 606 |
| 630 mm | from 621 to 720 | from 607 to 706 |
| 730 mm | from 721 to 820 | from 707 to 806 |
| 830 mm | from 821 to 920 | from 807 to 906 |
| 930 mm | from 921 to 1020 | from 907 to 1006 |
| 1030 mm | from 1021 to 1120 | from 1007 to 1106 |
| 1130 mm | from 1121 to 1220 | from 1107 to 1206 |
| 1230 mm | from 1221 to 1320 | from 1207 to 1306 |
| 1330 mm | from 1321 to 1340 | from 1307 to 1330 |
PROTECTIVE PLATES AND KICKPLATES
On request for 1 and 2 leaf Univer and Proget doors, specifying the side of application (pull or push).
Their main function is to protect the parts of the door that are vulnerable to being scraped by carts, hospital beds, etc. They are made of AISI 304 satinized stainless steel sheet metal with a standard height of 230 mm.
For on-site attachment with two-sided adhesive factory applied on the back, at the bottom of the door (kick plate) or at handle height (protective plate).
Protection plates
Kick plates
Holes are factory prepared for the passage of the handle panel and cylinder
Holes are factory prepared for the passage of the handle panel and cylinder.
DRIP-STEEL PROFILE
On request for 1 and 2 leaf Univer and Proget doors, specifying the side of application (pull or push).
It is applied to the exterior side of the door on site after being cut to measure, to be attached with the screws provided.
| Lengths avail. | FM L door leaf |
|---|---|
| 710 mm | to 800 |
| 810 mm | to 900 |
| 910 mm | to 1000 |
| 1260 mm | to 1350 |
WALL SCREWS FOR FASTENING WITHOUT PLUGS
Field of use: installation of Proget REI 60/120 and multipurpose doorframes to the wall or subframe using screws but no plugs. Designed for installation into concrete, full bricks, half-full bricks, lightened cement and other materials.
Advantages: saves time and money thanks to direct attachment of the frame to the wall, with no need to enlarge the holes for plugs. Thanks to the black galvanization, the screws blend in smoothly with the FC sealing.
| Dimensions | description | |
|---|---|---|
| Ø 7.5 x 50 mm | for attachment to metal subframes | |
| Ø 7.5 x 60 mm | for attachment to concrete and especially thick walls | |
| Ø 7.5 x 80 mm | for attachment to walls of average thickness | |
| Ø 7.5 x 100 mm | for attachment to walls of lower thickness | |
NOTE
Holes should be drilled using a Ø 6 mm stone drill bit.
SUBFRAME
Subframe (to be ordered) in hollow 30 x 15 x 2mm steel profiles (recommended for REI 60 and REI 120 Proget doors) equipped with anchors for mortar fixing and spacers that are to be removed during final installation.
Horizontal cross section
Vertical cross section